Change font size


Post a new topicPost a reply Page 1 of 1   [ 5 posts ]
Author Message
 Post subject: warning lights
PostPosted: Tue Apr 03, 2018 11:46 pm 
User avatar

Vehicle: 2010 Forester Diesel

Posts: 18
Location: Gold Coast
Has anyone come across the flashing red/ blue Temp light light, together with Hillhold and traction control light? Sometimes the steering light with it??

Usually they fo away again after switching the engine off and on a couple of times but not always..

Sometimes they come on after some driving. Other times when cold. The other day o had to drive it for a bit without steering assist. That was hard work...


Do I have some gremlins in my wiring??
Not sure yet if it's really the wet weather that makes it okay up more, as it does it intermittent.

_________________
Roland

2010 Frosty
2" lift, Snorkel, no EGR or DPF, 235/60/17, bashplate, sidesteps, rear wheel carrier, Aldi roofrack, tray and awning


Top
 Profile  
 
 Post subject: Re: warning lights
PostPosted: Wed Apr 04, 2018 7:52 am 
User avatar

Vehicle: MY09 XT

Posts: 35
Location: Canberra
Ive recently had this combination but also included standard CEL with traction and cruise disabled. Interested in any responses. I pulled a number of CEL codes using OBDII connector and Torque Lite app and in my case research seemed to indicate a faulty MAF sensor but this is just a guess.

Sent from my GT-N8010 using Tapatalk


Top
 Profile  
 
 Post subject: Re: warning lights
PostPosted: Wed Apr 04, 2018 7:17 pm 
User avatar

Vehicle: 2010 Forester Diesel

Posts: 18
Location: Gold Coast
I don't get any codes in the Engine

_________________
Roland

2010 Frosty
2" lift, Snorkel, no EGR or DPF, 235/60/17, bashplate, sidesteps, rear wheel carrier, Aldi roofrack, tray and awning


Top
 Profile  
 
 Post subject: Re: warning lights
PostPosted: Fri Apr 06, 2018 7:06 pm 
User avatar

Vehicle: S-edition

Posts: 2
Location: Perth
My SH9 displayed:

check engine light,
vehicle dynamics control light,
flashing cruise light.

I found that the MAF connector had some corrosion in it's plug connector, as a result of the detailer washing down the engine bay.

Unplugging and re-plugging the connector multiple times cleaned the contacts, which immediately cleared the above warning lights without having to do any resets.


Top
 Profile  
 
 Post subject: Re: warning lights
PostPosted: Sat Apr 07, 2018 6:25 pm 
User avatar

Vehicle: 2010 Forester Diesel

Posts: 18
Location: Gold Coast
I hooked up the Snapon scanner again.

I do have Can bus faults in ABS and Traction controls.. no faults in engine however. Looks like torque only picks up on Engine codes

I am pretty sure its some connector with corrosion. Might have to open them all and clean/ lube them up

_________________
Roland

2010 Frosty
2" lift, Snorkel, no EGR or DPF, 235/60/17, bashplate, sidesteps, rear wheel carrier, Aldi roofrack, tray and awning


Top
 Profile  
 
Display posts from previous:  Sort by  
Post a new topicPost a reply Page 1 of 1   [ 5 posts ]


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
"Takka LE" for phpBB3